A washing machine is one appliance almost every household has because it makes washing easier. However, it can also be faulty sometimes which is why you are properly looking for a solution and came across the guide on How to Fix a Washing Machine.
Nevertheless, in this article, we will be listing out 9 common problems of a washing machine and how to actually fix the. So if this interest you, i will advise that you carefully read this article till the end because even if yours is not faulty now, it could be tomorrow and the knowledge from this guide will save you a lot of time and money.
How to Fix a Washing Machine: 9 Common Problems
1. The washing machine wiggles
While a washing cycle is running, it’s normal for your washing machine to vibrate and move a little bit. However, if your washing machine starts to bounce around or move a lot, this means it needs to be repaired.
When the washing machine isn’t flat on the ground, this issue is most frequently caused. Grab a bubble level and see if your washing machine is level; if not, adjust the legs to make it so.
This will solve the issue. Ineffective suspension rods are the next likely explanation if that isn’t the issue. Your washing machine may occasionally become detached as a result, which will cause it to move around erratically. The suspension rods must be replaced if they are broken.
2. Noisy washing machine
When the washing machine starts to make loud noises while functioning, that is the next typical issue. The majority of the time, this is brought on by a coin or other piece of dirt bouncing about in your washing machine. Simply taking the item out of the washer will stop this from happening.
Another potential reason for it is a malfunctioning internal part, such as the motor, although this will require the assistance of a trained expert.
Read also: How to fix hardware problem in Android.
3. Clothing Is Ripped
If your clothes or linens come out of the washer torn or holey, your washer is broken. This problem is another one that is typically caused by anything that shouldn’t be in your washer, like a sharp piece of plastic.
It can also be caused by your articles becoming tangled up around the center pole, so make sure your clothing and linens are positioned correctly in the washing machine.
4. Drainage Issues
If your washing machine isn’t draining properly, an obstruction in the machine’s drainage system is possibly to blame.
The filter is the component that is most likely to be impacted since filters frequently become clogged with particles. All you have to do is look for obstructions in the filter and clear them if you discover any.
It’s a good idea to give the filter a regular cleanout in order to prevent this from happening again.
5. The Washing Machine Is Not Spinning
If your washing machine isn’t spinning, the problem can be something straightforward that you can fix yourself or something more challenging that needs professional assistance.
Start with the obvious cause. The most frequent problem is when there is too much clothing or linens in the washer, which prevents the washer from spinning. So make sure it isn’t overloaded and take some stuff out of it if it is.
If it doesn’t resolve the issue, it was probably brought on by a malfunctioning internal part, like the control board or the motor. It is important that you remove the washer panel before preparing them, you can use a multimeter for inspection.
They must be replaced if they are broken. You’ll likely need to hire a skilled technician to complete these repairs because they require the appropriate tools.
6. Water Doesn’t Fill Up in the Washing Machine
The best place to start when your washing machine isn’t full of water or isn’t filling at all is to inspect the water hoses, which can occasionally become kinked or obstructed.
To accomplish this, all you have to do is discover the hoses, inspect them for obstructions or kinks, and fix them as necessary to allow water to flow freely through them. Additionally, make sure that water is flowing from the faucets; if not, this could indicate that your water has been cut off at the main or that you are suffering an outage.
7. The washer door will not open
If the door of your washing machine won’t open, the water in your washer is probably the main culprit because it prevents the door latch from opening.
By starting a new cycle on your washing machine, you should be able to drain the machine and unlock the door. Once the door is open, you must check the drain and filter to make sure they are clear of obstructions.
If your door won’t open even when there isn’t any water inside, the control board or a defective door switch may be to blame. You’ll need to call a specialist to accomplish it for you because these internal components will need to be tested with a multimeter before being fixed or replaced.
Read also: How to fix a Mac or Macbook that won't turn on – Best and Working Methods 2023
8. Washer Odor
A buildup of bacteria and grime in your washing machine is likely the cause of any unpleasant smells. This is frequently brought on by using just cold washes and detergent that remains after a cycle and over time turns into dirt and emits an odor.
Run your washing machine on the hottest setting on an empty cycle to get rid of the odors. This will almost always get rid of the odor. It’s a good idea to regularly clean your washing machine to prevent this from happening again.
9. The washer won’t start
The most frequent reason for your washing machine to not start or to stop in the middle of a cycle is an issue with the power source.
To resolve this issue, make sure the circuit breaker that powers your washer is turned on, and if it isn’t, turn it back on.
If the issue persists, a repair will be required. Whether the circuit breaker is functioning properly, try plugging your washer into a different power outlet to check if it operates. If it does, the power outlet is broken and has to be fixed.
Conclusion
We hope this guide on how to fix a washing machine has been of help. However, if your washing machine is experiencing any issue that is not listed here, then we will advise that you probably take it to an engineer to identify and fix it.
This is because any issue not listed here are those that need engineers trained in that field to actually help out.
